Electric heater 1200W ElectricSun white infrared heating panels with thermostat

ElectricSun electric heater power consumption

On average, in winter, a device actually operates between 2 and 12 hours, on average 6 to 8 hours a day, if our recommendations are taken into account and if the actual situation of the room is reported.

If the radiant panel is smaller than our recommendations or the actual situation of the room is not correctly reported, the panel may not cover heat loss and will run for longer, even does not reach the temperature you want, and the panel life will be shorter, and the monthly power consumption will be higher.
The longer the radiant panel is, the longer the panel life, and the longer the monthly current consumption is NOT, the panel heats up faster and the thermostat will turn it off. The efficiency of the panel is higher also due to the higher power and the larger size.

Electricity consumption is relative and depends on the following factors influencing consumption:
- the power of the panel (if the panel is sized correctly, not to be smaller, if it is larger does not consume you more);
- the supply voltage 220 – 240 Volts, not to be lower;
- the outside temperature (depends on the geographical area);
- the degree of thermo-isolation of the room (heat loss - heat);
- the number of exterior walls;
- adjoining rooms if heated or unheated,
- the number of windows and the surface of the windows;
- the type of carpentry and glass and their quality;
- the opening of windows and doors;
- the setting of the thermostat, etc.
The disadvantages of the room, meaning heat losses are disadvantages no matter what type of heating system you use.

Example an 19 m² room with 2.5 meters high (=45m³), a thermally insulated exterior wall with 10 cm polystyrene, with 2 m² double glazing, four heated adjoining rooms and the thermo-insulated floor, the temperature set in thermostat 22°Celsius, has an ElectricSun 960W panel (= 50 Watts/m²).
It means 5.8 kw/day, that is 174 kw/month.

ElectricSun electric heater power consumption

INSTALLATION INSTRUCTIONS COMMISSIONING AND MAINTENANCE ElectricSun
Electric heater, outdoor heater, electric patio heater, panel heater, infrared heating panels, electric panel heaters, electric heating system.

• ElectricSun electric heater works with 230 Volt single phase electrical current (220V - 240V), 50/60 Hz;
• The panel must be connected to the mains, a separate circuit (dose or socket). STECKER - plug can be cut.
• A separate phase electric circuit means:

A 10A fuse, wired-thick copper conductor 1.5 mm² - MAX 2.000 Watt
A 16A fuse, wired-thick copper conductor 2.5 mm² - MAX 3.200 Watt
A 20A fuse, wired-thick copper conductor 4.0 mm² - MAX 4.600 Watt
A 25A fuse, wired-thick copper conductor 4.0 mm² - MAX 5.200 Watt
A 32A fuse, wired-thick copper conductor 6.0 mm² - MAX 7.000 Watt

• We recommend to be installed by a qualified electrician.
• It can be mounted on drywall (plasterboard) with dowels type drywall anchor METAL.
• The panel is secured through holes in the frame with 4 screws in the ceiling or wall plugs (wall) and connecting to the network, then put ornamental caps to conceal fixing holes.
• Attention! if the ceiling is not right the panels do not stick, do not tighten the screws to amaximum on the ceiling-wall, panels have to stand right in spirit level.
• To gain maximum efficiency it is good for the panels to be mounted on the ceiling, as close as possible to the center of the room (symmetrical) with small side panel directed towards to the window, at a distance of at least 1m from the window.
• Ideally, the distance from the corners of the ceiling panel and floor corners to be less than 3-4m because the panel radiates in the the same time the four walls and on the floor, if you put on the wall, that wall and some of floor not radiate anything, it will heat the room but the panel will operate more than 10-50%.
• The panels can be mounted and side walls of the room (inside wall, not glass wall with no window on the opposite wall, the bottom of the panel to be at a distance of 1.5 meters from the floor, like a painting) or if the rooms are more than 3 m tall,it is good for the panels to be mounted on the wall at maximum 2.5 m, sloped at 45 degrees to the ceiling, but in this case the efficiency decreases by 10-50 %.

BEFORE SUPPLYNG TO 230V REMOVE PROTECTION FOIL IF IT IS!

• Some heated have built-in thermostat.
• Wired thermostat is on the power cord as a classic switch.
• It is recommended one thermostat in a room and if we have several panels.
• It is recommended one thermostat and if we have 2-3 rooms that communicate with each other doors are opened without ex .: living room-dining room-hall-staircase-kitchen and so on.
• Thermostat will be installed on the interior wall on the middle(central) at a height of 1.5m from the floor or after the eyes of the owners. Please note! The thermostat is not obstructed and influenced by warm air or cold;
• Attention! the amperage thermostat in case of panels over 1200W or 3200W or several panels when installed in a room, if necessary use a contactor (pole single phase 25A, 32A, 40A etc. or right);
• The thermostat regulates the desired temperature in the room,after the panel is dealing with your thermal comfort. (The panel has one power if you set the thermostat higher temperatures will NOT warm faster)
• Cleaning the panel (DISCONNECTED FROM THE POWER SUPPLY)with a non-abrasive material,as soft as you can (cotton, microfiber), slightly moist and without any cleaning solutions. Do not cover. Don`t touch.
• Non-stop use will shorten the use life of the heaters, so a break after every 12 hours use if possible.